# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
# 

    FontPath	"/usr/X11R6/lib/X11/fonts/misc/"
    FontPath	"/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath	"/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath	"/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath	"/usr/X11R6/lib/X11/fonts/100dpi/"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    NoTrapSignals

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    DontZap

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    DontZoom

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol	"Standard"

# when using XQUEUE, comment out the above line, and uncomment the
# following line

#    Protocol	"Xqueue"

    AutoRepeat	500 5

# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1))
    Xleds      1 2 3

# Turn off the silly X key mapping (instead of using loadkeys)
     XkbDisable


# To set the LeftAlt to Meta, RightAlt key to ModeShift, 
# RightCtl key to Compose, and ScrollLock key to ModeLock:

    LeftAlt     Meta
    RightAlt    ModeShift
#    RightCtl    Compose
#    ScrollLock  ModeLock

EndSection


# **********************************************************************
# Pointer section
# **********************************************************************

Section "Pointer"
    Protocol    "PS/2"
    Device      "/dev/psaux"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Protocol	"Xqueue"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Emulate3Buttons
    Emulate3Timeout    50

EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "TI Travel Mate 6000 Active Matrix"
    VendorName  "Texas Instruments"
    ModelName   "TFT 12.1"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync	30-64         # multisync

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-90

# Modes can be specified in two formats.  A compact one-line format, or
# a multi-line format.

# These two are equivalent

#    ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace

#    Mode "1024x768i"
#        DotClock	45
#        HTimings	1024 1048 1208 1264
#        VTimings	768 776 784 817
#        Flags		"Interlace"
#    EndMode

# This is a set of standard mode timings. Modes that are out of monitor spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.

# 640x400 @ 70 Hz, 31.5 kHz hsync
Modeline "640x400"     25.175 640  664  760  800   400  409  411  450

ModeLine "800x600"     36      800  824  896 1000   600  601  603  625

Modeline "640x480"     31.5   640  680  720  864   480  488  491  521

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Generic VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"
    Chipset	"generic"

#    VideoRam	256

#    Clocks	25.2 28.3

EndSection

Section "Device"
    Identifier  "Cirrus Logic GD7548"
    VendorName  "Cirrus Logic"
    BoardName   "clgd7548"
    VideoRam    1024
    # Chipset	"clgd7548"
  #  Option "linear"
    Option "power_saver"

# Use Option "no_bitblt" if you have graphics problems. If that fails
# try Option "noaccel".
# Refer to /usr/X11R6/lib/doc/README.cirrus.
# To allow linear addressing, uncomment the Option line and the
# address that the card maps the framebuffer to.
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

Section "Screen"
    Driver      "svga"
    # Use Device "Generic VGA" for Standard VGA 320x200x256
    #Device      "Generic VGA"
    Device      "Cirrus Logic GD7548"
    Monitor     "TI Travel Mate 6000 Active Matrix"
    Subsection "Display"
        Depth       8
        # Omit the Modes line for the "Generic VGA" device
        Modes       "800x600" "640x480"
        ViewPort    0 0
        # Use Virtual 320 200 for Generic VGA
        Virtual     800 600
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "800x600" 
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
#    Subsection "Display"
#        Depth       32
#        Modes       
#        ViewPort    0 0
#        Virtual     640 400
#    EndSubsection
EndSection